by Smr162 on 06-18-2013 07:54 AM

Ok so this guitar is a vintage lemon drop, all wilkinson hardware and it has a mahogany neck and body.
by William G. on 06-18-2013 07:46 AM

Preamps and high-end converters used with Protools 10 in the studio with an Imac, a TC FINALIZER connected AES EBU to sleep sound in Protools, a TC Reverb 4000 ADAT and EVENTDE ECLIPSE back online for other effects. Great to have a hell of a setup.
by Smr162 on 06-18-2013 07:24 AM

Beautiful honey mahogany neck
Finger board is Indonesian rosewood
Head stuck is stunning
High gloss finish
by jesussaves on 06-18-2013 07:16 AM

Micro assuming Super Distortion which would have added a bit of power, and which might have altered the EQ.
Compared to its predecessor, it sounds cooler, more pronounced in the midrange and treble ... It sounds excellently on all plans shred solo. Warning, his personality is quite pronounced: ca like or not. According to the agreements or solo play that was sometimes almost like a wah is engaged. It refers especially in terms a little speed. Frankly, to play shred, you can go with your eyes closed. It sounds less aggressive than Evolution, more powerful and less medium that FRED, a more balanced Blaze Custom ... I find it more piercing in the mix a PAF PRO ... In short, try not to priori!
by contorsion on 06-18-2013 05:05 AM

No rack but relatively compact compared to the majority of cattle in its class.
modular, if you have a few parts you can easily adapt to the situation at hand, as you rather need additional channels or groups. mine is 14/4/2 configuration with a master module, and to a stereo compressor.
Standard connectivity Jack / XLR
by:
mic in (XLR)
line in (jack)
Direct output (jack)
channel send (jack)
channel return (jack)
Note that the send / return (insert anything) is done by using two mono jacks and not a single stereo.
per group (while jack connector)
- Having external meter
- Exit sub group
- In line
- Pan in external
- Output PREFADER
- Entry PREFADER (insert wholesale)
the master
- Output XLR and jack
- Insert (always in and separated out)
- In line
Auxiliary: there are 4 accessible from every, this is a normal way, a group or even the master
the equas: slices on mic / line only. acute low switch with respectively 12/8 and 150/60
NOTE
gain only applies to the mic inputs. For line level, only the fader is active
mute on each channel, but not solo.
most consoles (including mine) are modified with external power supply (...) and phantom power.
THE compressor is either dual mono or stereo, with input gain and output ration, attack and release.
9/10 only because of the gain on the mic inputs. Otherwise, I knew to buy.
by zenza on 06-18-2013 03:48 AM

Owner of a Fender Stratocaster Standard Mexico more than a decade, I was very satisfied with the beast, comfort, Fender typically short, the marriage of convenience.
I found the sound a bit flat, the middle pickup tasteless, but you know ... Change the pickups, probably yes, but what game what his microphone? Fender, Fender not, the choice is so extensive :-(
And then, by dint of reading rave reviews on micro Tornado MS, I thought the game was worth the candle still surely. My choice is the set Strat'60s L series
So decided I contact Marc, two mail exchanges later, I told him that I weld as a lumberjack, and the guy offered me a plate full climb, the knobs on top + no-load tone, of all good, easy to assemble. Banco, I took the leap.
Barely a week later, I receive the package, get the plate / fingers in the nose.
And there friends, it's as if everything had changed. My amp sings, my fingers find the notes more clearly, all the sounds are excellent! It is as if the entire spectrum was extended, deep grave, beautiful, crystal-clear highs, dynamics madness ...
For a first attempt, a real coup! Marc has gold in his hands, it makes you a guitar series, one model that you do not let go.
A real slap.
by kaktus666 on 06-18-2013 03:22 AM

Looper for sampler bocles some 15 minutes, divided into 11 banks.
Several battery accompaniments are available, more or less usable.
Ability to create loops in 3 or 4 times.
The technology is digital.
by obug01 on 06-18-2013 02:49 AM

Made by the Fender custom shop in the U.S..
Alder body
Channel 1 piece maple
Form "C" thin-shouldered 1983
Maple fingerboard
184mm radius of the key
21 vintage-style frets
1 neck pickup single custom hand-wound Fat '50s Strat
1 micro middle single custom wound strat
1 single pickup Seymour Duncan SSL-5 Strat
American Vintage Synchronized tremolo with custom black
Mechanical Fender / Gotoh vintage style
Hardware nickel / chrome
1 black plate fold
Scale 648
Nut Width 42.5mm
Strings GHS DG Boomers, nickel plated steel
Rods .010, .012, .016, .028, .038, .048
Deluxe black hardshell case
Comes with guitar cable Evidence Audio High-End Custom Leather Strap, GHS DG bass strings, pick DG album "Live in Gdansk" 3 CD + DVD, Phil Taylor's book "The Black Strat", cloth and certificate authenticity
by Cuki79 on 06-18-2013 02:47 AM

Transistor preamp with transformer coupling in and out.
inputs and outputs XLR and TRS output + tuner and loop insertion
3-band EQ with parametric medium.
The knobs are weaklings.
by fometto on 06-18-2013 02:26 AM

It is a product that does not do its job and degrade the sound so horrible.
Supposed to work on a 50W amp it Brullé the smoked on my head hughes and kettener Statesman.
Do not buy!
by NSEaProtector on 06-18-2013 12:38 AM

How long have you use it?
4 years (disco)
What is the particular feature you like best and least?
The sound
To expand a little more, I find the lens, it breathes, it is very powerful and dynamic!
I would say the least weight but fixed installation is not important ...
Have you tried many other models before buying it?
Yes I had a crest (it there's time) the crown, the QSC, the EV to mention only the best known.
How would you rate the quality / price?
Excellent.
With experience, you do again this choice? ...
I would change all my amps for the Ecler, then yes I'll make sure to replace my current amp for the DPA.
by ZikaBoom on 06-18-2013 12:25 AM

Made in the USA, we selected all the items on the configurator on the site, and receive a kit. I took the microphone separately Lindy Fralin.
Mine is standard alder body maple neck (bird eye maple) rosewood fingerboard, micro precision.
It sounds of thunder, simple effective, powerful, exemplary finish.
I chose thinner frets, super nice.
by ZikaBoom on 06-17-2013 09:03 PM

Amp transistor, the excellent 700 RB II
HP 12 "neodium.
The amp is very comprehensive, it is the same as the big brother 1000 RB are
On the site of GK are summarized below:
480 watts (4 ohms) plus 50 watt
Horn bi-amp system
• Active 4-band EQ
• Adjustable contour presence
& 4/5 string voicing
• Boost (valve effect)
• Separate woofer & tweeter
volume controls
• Effects loop & tuner out with mute
• XLR out with level, ground lift
& Pre / post switch
• Speakon & 1/4 "outputs
• 19 × 3.5 × 8 (2 space)
• 19.5 lbs.
Since this model is not on here audiofanzine the info.
by christian.patou on 06-17-2013 07:25 PM

I wanted a new micro STIMER DUPONT therefore to give to my son but it is zero. It was not the sound of my STIMER YVES Guen is only a pale copy, it is misleading to believe that musicians it is the micro Django. Now there are amps I am afraid that is the same and at what price,
by Aurochs4 on 06-17-2013 07:09 PM

I think everything has already been said!
Lack a USB or Firewire port, but in 1991 .... ! For 1991 it is simply the top of what we were doing.
by Banya on 06-17-2013 06:31 PM

- Loop or one shot
- Tap tempo
- 11 sentences
- Guides tempo / phrase
- No lamps
- Jack connector
by ekmusikprod on 06-17-2013 06:04 PM

For Particular features, look on the Korg site.
The PA50 is equivalent to PA50D except the floppy drive now replaced by an SD memory card.
by hades le dik-sa on 06-17-2013 06:02 PM

we will return pa thousand times on the table that everyone knows ...
by jesussaves on 06-17-2013 05:21 AM

In summary, distortion pedal ultra-strong, ultra-high-gain-gain so high that you can not adjust the gain: just volume and 3-band EQ. The gain is set to 11 and pulls the ears to the delight of apprentices metallurgists. Personally, I had the first version, the one with the little foot switch (so no republishing by Digitech).
by wenderssoul on 06-17-2013 04:27 AM

Channel pleasant, with good access to acute. This is not a Strat, but it's not what you asked.
by killer31 on 06-17-2013 03:46 AM

How long have you use it?
About 1 year for use discomob '
What is the particular feature you like best and least?
Most would qualiter Sound RCF. But also handles that are well thought out.
The moin is the lack of bass.
Have you tried many other models before buying it?
No
How would you rate the quality / price?
Fine
With experience, you do again this choice
Oh yes!
by Taquet2012 on 06-17-2013 03:39 AM

I use it for several months. I'm a guitarist and touch all that leads me to have many pedals. Very nice to have a lot of pedals, but it quickly becomes tedious when regularly changing sounds. With this machine, the problem is solved.
The machine (which seems very solid) is very easy to configure, each footswitch can have the function that you want. Importantly, there is no latency between each preset!
Wholesale bonus, there are six outputs to drive the pedals (which saves space), the ability to control 3 units morning (and that's still top), and an integrated buffer.
The downside? Come on, it lacks the ability to choose the chaining effects so it must reflect a chaining her before fixing everything and then a small screen to record their presets / functions on the footswitch was great but that's quibbling.
The quality / price? I do not know I do not know of any competitor in any case it is an investment that I do not regret.
Finally if you use the effects loop of your amp I recommend MIDI 4x loop to take full advantage!
by Maxidingue on 06-17-2013 02:43 AM

Installation is tedious and time consuming on my brand new iMac i5 nice but the game your candlelight
Several hours for me so plan to do it before 22 hours or you will spend the night
Not really inconsistent, even works with version 1.3 of the software my MPC Renaissance
Operation is very simple if you stay in the basics, then we can easily get into the guts of the app and, it is complicated but not insurmountable
No real manual, but a nice collection of overly didactic video uttiles
by jesussaves on 06-17-2013 02:21 AM

Take a mahogany Ibanez S, put him two EMG, and boom! This is the S920!
I love what comes out of the box, and this is Ibanez S920 in this case! Light, well made, beautiful, ... It is designed to play sounds pretty accurate because it has an EMG 60 in the neck (instead of the usual 85) and an EMG 81 in acute. I like the fact that it has 24 frets and it has a small 3-position selector (like the one found on the Ibanez John Petruccci) rather than a selective style Start '. One volume and no tone. We feel it is intended to be efficient and direct!
Another plus: it comes in a semi-rigid case and a multi-function tool.
Small problem: the plates that cover the cavity at the back of the guitar are screwed on top of the timber without planning for it (ca exceeds the body). It's a bit rude, but as it is behind, it does not show
by ozzy ozburne on 06-17-2013 01:29 AM

Japan manufacturing, mine in 1989. Basswood body, maple neck, rosewood fingerboard, floyd Ibanez works nickel after 24 years (!?), Flat end 24 frets, HSH config handle, 1 volume, 1 tone. In short, a Jem.
This is a relatively limited edition as manufactured in 89 and 90. Black marks pyramids pearly whites, white pickups (2 paf pro and single Dimarzio). A large handle in the body cavity dug floyd. The last 4 boxes scalopées. Go see the side of Jemsite for more details.
The Mecha take the agreement, floyd is indestructible. Very soft tone, very musical, great. In habits, I am not using the tone, I have also not put on my Warmoth.
It is relatively heavy (as much as my LP on the scale), but the weight and balance are better distributed and it seems lighter than it actually is.
RAS, well done, finishing blameless, top quality wood (rosewood of the key dark and dense, is gorgeous).
I love the look, it's class and typed both sober and flashy at the same time ... I bought Passion and Warfare in CD when it was released in ... 1990 already ...
by bert'nortt' on 06-17-2013 01:27 AM

eyes closed, all leather with impeccable quality and durability ... for a price defying all competition, is 3-4 times less expensive than other brands ... main reason for this "review" ... First one, bought by Coores' as it is in brand Tho / Tho...pour see ... No disappointment because very attentive to the comfort of a strap, you are aware that finds out quickly with use. Very wide, although flexible, it does not come bruise or cut shoulder ... So in the week after I bought two other black on a price range from 16 to 18 euros! But mostly leather, the width of 7 cm for me and all my guitars, they are well positioned even those who are "the weight", it avoids the tensions of maintaining the handle. Complete the look by installing locks "STRAP / LOCK locking" (low price / cost 5.80 E 'as the price differs from those at 25, it's reliable air with a nut against I do not think I take any risks) ... For the length as the picture using all the "interlacing and jumps recesses settings, the leather does not crease, preferably large part forward to good" strapper "the shoulder, you see.
.... A highly recommend beginners to the most experienced Professional!.
by jesussaves on 06-17-2013 01:13 AM

Everything has been said before! I appreciate the frets not too large, the overall balance, excellent finishes
Note that I am especially electric guitarist, but in terms of acoustics I trèèèèèèèèèès demanding sound plan! I have tried many models and brands, but nothing has really convinced me (except some Ovation) until I tried the Taylor. And then a slap!
by ZeroFromKellen on 06-17-2013 12:45 AM

made in vietnam
easel tune kind O'Matic
U handle quite late
22frettes
LH100 pickups esp splitable
two volumes and a Mastertone
by ZeroFromKellen on 06-17-2013 12:17 AM

this guitar is made in Indonesia
vibrato flutant
the handle is a profile
24frettes jumbo
1 micro PSND1 Ibanez (neck) Ibanez PSND 1 micro-S (middle) 1 micro PSND2 Ibanez (bridge) in config MSM
a volume and a tone knob 5positions